Tensile-manufacture,factory,supplier from China

1. Comparison of copper pipe and stainless steel pipeNow from the material's physical performance, health performance, corrosion resistance, economic value and other aspects of comparison.1. Comparison of physical propertiesComparison of tensile strength:Take the commonly used 304 material of thin-wall stainless steel pipe as an example, its tensile strength is 530 ~ 750Mpa, is galvanized pipe 2 times, copper pipe 3 times.

Stainless steel rolls in accordance with the method of classification can be divided into cold rolling and hot rolling two, if it is in accordance with the structural characteristics of steel classification, can be divided into 4 categories, respectively, austenitic stainless steel, ferritic stainless steel, martensitic stainless steel and precipitation hardening stainless steel.Cold rolled stainless steel coil in order to ensure its yield strength, tensile strength, elongation and hardness and other mechanical properties, steel coil in the production of the need to undergo annealing and solut

  Inconel625 alloy is a solid solution reinforced nickel-based deformation high temperature alloy with molybdenum and niobium as the main strengthening elements, has excellent corrosion resistance and get oxidation properties, from low temperature to 980 ℃ have good tensile properties and fatigue properties, and resistance to stress corrosion under salt spray atmosphere, so it can be widely used in the manufacture of aero-engine parts, aerospace structural components and chemical equipment, the alloy is used in the manufacture of Engine magazine, guide blade, mounting edge and barrel, fue

       Incoloy 925 is an age-hardened nickel-iron-chromium alloy with additions of molybdenum, copper, titanium and aluminum. The chemical composition of this alloy is designed to provide a combination of high strength and excellent corrosion resistance. The nickel content is sufficient to prevent chloride ion stress corrosion cracking. Nickel, along with molybdenum and copper, also provides significant resistance to chemical reduction. Molybdenum helps resist pitting and crevice corrosion. The chromium content of the alloy resists oxidizing environments.

Inconel 600 alloy has the following properties.        1. good resistance to corrosion by reducing, oxidizing and nitriding media        2. good resistance to stress corrosion cracking at both room temperature and high temperature        3. good resistance to dry chlorine and hydrogen chloride gas corrosion        4. good mechanical properties at sub-zero, room temperature and high temperature        5.

Introduction:Alloys comparable to Incoloy 825 alloys are high Ni, highly corrosion-resistant nickel-based alloys with extremely high corrosion resistance to both oxidizing and non-oxidizing acids.Incoloy 825 alloy has good general corrosion resistance to both oxidizing and non-oxidizing acids due to its rich content of Cr, Mo and Cu. In particular, it has extremely high corrosion resistance to sulfuric acid. Due to the high content of Cr, Mo and Ni, it has excellent pitting corrosion resistance, crevice corrosion resistance and stress corrosion cracking resistance in chloride environment.

The 2mm thick braided stainless steel plate is made of austenitic SUS316 stainless steel, and the partition is mostly 500mm x 4500mm. The panel is fixed to the aluminum alloy subframe by tapping nails, and then assembled by the aluminum alloy subframe and the unit mullister to form a stainless steel unit system. The calculation of the panel support system is analyzed according to the large deformation theory.

Carbon metallicCarbon metallic is primarily based on positive standards, which, if observed, might come below the carbon metal category. the few factors or the requirements to be stored in mind earlier than classifying into the identical are-There may be no specification of the minimal content material required for certain things like- nickel, titanium, cobalt, chromium, molybdenum, etc.

When choosing substances for use in industrial applications, it's vital to recognize how exceptional metals compare. Two frequent selections are Monel and SS316. Both of these metals have special residences that make them perfect for positive uses, however which one is better? Here's a contrast to assist you decide.What is Monel?Monel is a nickel-based alloy composed especially of copper and nickel. This aggregate creates an alloy with splendid electricity and corrosion resistance, as nicely as exquisite electrical and thermal conductivity, making it best for a range of applications.

301 stainless steel strip is a sub-stable austenitic stainless steel with a fully austenitic organization under full solid solution conditions.The austenitic stainless steel has a fully austenitic organization under full solid solution conditions.In the austenitic stainless steel, 301 is Z easy cold deformation strengthening steel, through cold deformation processing can make the steel strength, hardness, and retain sufficient plastic, toughness, plus this steel has good rust resistance in atmospheric conditions, but stainless steel micro-wire in reducing media corrosion resistance is poor, in